* Added QMK support for GSKT-00, PaladinSplit, PaladinTKL and PaladinPad pcbs
* Remove the paladin boards from this PR
* Changed gskt00 as per review comments. Added two new default layouts, 60_ansi_tsangan and 60_iso_tsangan
* Fix the layouts/default/60_iso_tsangan/layout.json file
* Removed ? from rules.mk, removed unused fn_actions from keymaps. Changed the 60_iso_tsangan to work correctly
* Removed PREVENT_STUCK_MODIFIERS
* Keyboard: add Keyboardio Model01
This port implements key scanning and everything in their default
keymap.
It doesn't implement mouse warping; QMK can't do that (yet).
LED control is mostly not implemented. The ability to set all LEDs is
included because they can get stuck on coming from the bootloader
otherwise. Single LED control is also implemented for numpad indication.
The scanners also support batch LED transfer which is what you'd need if
you wanted to do fast effects. Gamma correction is also not implemented,
but is present in the original firmware. The necessary info for further
implementation is in the KeyboardioScanner module for Kaleidoscope.
To install on your keyboard:
make model01:avrdude
When prompted, hold the "prog" key on the keyboard to put it into
programming mode. This can also be achieved by holding the "prog" key
while plugging in the keyboard. This works even if the firmware is
corrupt or missing.
Hot plugging the halves seems to work fine, but there is no explicit
support for eg. making sure the matrix scan rate is reconfigured.
* model01: clean up includes and include guards
Uses #pragma once everywhere.
* model01: split LED and matrix code
This makes space if someone wants to implement better LED support
later on, the keyboard is a lot more capable than the current code.
* model01: separate I2C timeouts for matrix vs. LED
If the scanners have no data they don't ACK reads and just time out.
So we want a pretty short timeout to keep scan rates high.
Meanwhile the LED transfers might take longer - I don't know though,
so here we are conservative.
* model01: implement better LED control
- gamma correction from the manufacturer's firmware
- suitable delays to allow back to back LED writes
- this is fast enough to write the whole keyboard without noticeable
delay, in my experience
- minor bug fix: RHS Fn key was not addressable
* model01: add license to wire-protocol-constants.h
* model01: replace gamma LUT
The original was of unclear license origin. This one is functionally
identical and includes a generator should people wish to adjust it.
* model01: use the already-present CIE1931 lightness curve
...rather than baking in another gamma curve.
It's said that CIE1931 is the right thing to be using rather than gamma.
OK. Let it be so.
* model01: call matrix_init_user() from matrix_init_kb()
* model01: remove inapplicable config options from rules.mk
* model01: readme.md: update build environment links
* Add flashing instructions for Linux
* Make device/manufacturer name consistent for ymd96
* Disable command mode by default for YMD96
* Add function call to fix backlight for YMD96
* Add personal YMD96 config
* Replace include with QMK macro
* Move KEYMAP macro to keymap-level folder
* Move custom KEYMAP macro to global LAYOUT_iso macro
* Change transparent keymappings to global definition
* Remove unecessary import and change to pragma once
- (instead of repeated ifdef)
* Remove global keymap/layout definition
* Remove chording as it is not documented, not used, and needs work.
* Make Leader Key an optional feature.
* Switch from `PREVENT_STUCK_MODIFIERS` to `STRICT_LAYER_RELEASE`
* Remove `#define PREVENT_STUCK_MODIFIERS` from keymaps.
* Arrow keys are now arranged on hjkl (vi style)
* The escape key is moved on capslock, shared with func layer switch
* The grave key is now dedicated (not shared with escape)
* Add a new numpad layer that can be activated with the spacebar
* Fix layout mismatch between layers
* Use bult-in underscore KC_TRNS alias
* add my config
* fix backlight, clean up that code
* group background code, restore static var
* qwerty is supposed to be in the middle
* wrap layer change backlight in ifdef
* backlight levels and some more 'emojis'.
* Restructure to make it possible to press cmd ent on the right side of the board with one hand.
* Expose the period through the number layer. Add Hyper keys to mouse layer
* reduce mouse speed
* add a : -P key
* Thumbs up and down, remove some keys that are duplicated via function keys, clean up
* fix build issues
* add various emoji
* duplicate default Meira keymaps
* Miera updates
* add documented but unmapped emoji
* Sound for the Meira, was stumped by a file size! Thanks drashna!
* add docs
* docs
* revert lib changes...
* clean up
* clean up
* remove make file
* Fixes missing key
* clean up
* add my lets split
* add more emoji
* add the telophase board (unofficially, I guess...)
* add missing files
* add/reset files
* Review feedback implementation: Not needed. Add #define FLIP_HALF to your config.h file instead.
* Review feedback implementation: All of these includes should be replaced with #include QMK_KEYBOARD_H.
* Review feedback implementation: [FAILING] You may want to use LAYOUT_ortho_4x12 instead, and move this to /layouts/community/ortho_4x12/ instead. That way, you can use the same keymap for all of the boards.
* clean up
* add a key for command tilde (osx loves it)
* at least its building again
* remove adjusts and migrate layer switching to MO(_LAYER)
* update the telophase readme
* update the telophase readme
* grahampheaths -> grahampheath
* ONEHAND_ENABLE -> SWAP_HANDS_ENABLE
* convert lets split to use ortho_4x12
* Move lets split keyboard layout into community/ortho_4x12
* make telophase use LAYOUT()
* I did it?!
* Add clap and grin
* swap tabs and back and forward
* whitespace
* Add ellipsis and thanks emoji
* Move flip_half to telophase config (conflicts with lets split layout)
* Use #pragma once instead of config_user_h
* remove unused stuff
* Initial version of zeal60
* WIP
* Fixes issue #900
* Adding RGB underglow functionality.
Fixed a compile-time conflict caused by enabling RGB underglow functionality.
* Refactor RPC protocol
* Fix last merge
* README for RGB underglow updated.
* Additional README changes.
* Adding RGBW strip software-based current-limiting functionality.
* RGBW current-limiting functionality should be handled by RGBSTRIP_MAX_CURRENT_PER_LIGHT instead.
* Updated README to reflect implementation of built-in current limiting.
* Keymap readability improvements.
* Minor keymap improvements.
* Fixed LED driver init sequence, formatting
* Dimming implementation tested, working.
* Stab LEDs synced with spacebar hits in effects.
* RGB underglow tested and functional. Simplified README for RGB underglow.
* Undid accidental file deletion from previous merge conflict. Safer values for RGB underglow.
* Improved arrow key positions in keymap.
* Added functionality to correct uneven RGB underglow. Refactored related code.
* Reverted to safer values for underglow.
* Changes for v0.3
* Custom LED brightness scaling will take place after current adjustment in order to avoid being overridden.
* Create keymap.c
Added split backspace and split shift to ISO layout
* Create config.h
Turned on LEDs for new layout
* Fixed bug where left spacebar stabilizer LED (LC06) would adopt color of row above.
* Added hhkb_wilba keymap
* Update keymap.c
* Update keymap.c
* Update keymap.c
* Added indicators, full param setting via host
* Added "mousekey" layout
* Added Zeal65 support, factory test mode
* Keycode safe range changed, caused bugs
* Bumped EEPROM version due to change in QMK keycodes
* Disable HHKB "blocked" LEDs if KC_NO in keymap
* Added "disable_hhkb_blocker_leds"
* Required overridden function for keymaps in EEPROM
* Added polar coordinate mapping, effect speed
* Force Raw HID interface number to 1 always
* Fixed last merge from master
* Added effect speed to default keymaps
* add BACKLIGHT_ prefix to vars
* add BACKLIGHT_ prefix to vars
* Keymap speed effect; keymap improvements/fixes
Readme updated to match changes
* Refactored to use common IS31FL3731/I2C drivers
* Fixed make rules, backlight disabled feature
* Make split rightshift default for Zeal65
* Added M60-A as a "version" of Zeal60.
* Renamed IS31FL3731 driver functions
* Fix suspend_wakeup_init_kb() being defined twice
* First pass refactor dynamic keymaps
* Updated to changed I2C and ISSI drivers
* Refactor zeal_color.* usage to quantum/color.*
* Updated Zeal65, fixed dynamic_keymap
* Major refactoring of Zeal60 backlight and API
* Lots of little cleanups
* Added readme.md
* Added readme.md
* Added LAYOUT_60*() macros, refactored and cleaned up default keymaps
* Fix compile error in suspend.c
* Added Zeal65 LAYOUT macros, info.json
* Added rama/m60_a, deleted zeal60/keymaps/m60_a
* Fixed rama/m60_a/keymaps/proto
* Fixed compilation error for suspend.c
* Requested changes for PR
* Fixed readme.md images
* Another readme.md fix
* Added drashna's requested changes
* move tv44 to thevankeyboards directory
* move bananasplit to thevankeyboards
* move roadkit to thevankeyboards directory
* add a basic readme
* update readmes to correct the make instructions and add more help text
* rename tv44 to minivan as per Jack's suggestions
* update readme
* rename tv44 to minivan
* update tv44 to minivan
* change includes for tv44 to minivan
* remove extra includes
* rename alf_x2 to alf
* rename to x2
* rename dependencies
* Fix readme
* moved x2 into alf directory
* update readme for make instructions
* move dc60 to alf directory
* update dc60 readme for make instructions
* change readme txt as per noroadsleft PR comment
* ALT keymap update
Added additional End key on layer 1 to match key cap
* LED driver update addressing PR #3871
Update sync between IS31FL3733 drivers is causing varying behavior in keyboards including brightness mismatch and slight flicker at very low rgb values. Visually, disabling sync is not noticeable. Ref PR #3871 by guarnacciaa.
* add SCREEN_NAV layer for copy/pasting within screen
* working readreg/paste macros
* working read reg / paste macros
* write log and tran patterns, and expand
* add ls -la shortcut, add tab on combined layer
* put delete word on the right pinky key on shell_nav layer
* add TAB on the right side, add reset key
* added Cloud9 macros
* add cloud9 shortcuts to atreus layout
* added BROWSER_CONTROL layer
* finalized browser control layer
* adding comment
* add browser control layer to atreus
* add flashing command line
* remove the tab on combined layer
* remove the tomouse
* remove mouse layer, change log/tran expand patterns, cleanups
* add dumptlog macro
* add "delete to home" shortcut
* fix conflict
* remove unneeded mouse layer
* add meh shortcuts on the browser_control layer
* add/modify some macros
* explain the various layers
* putty paste is right mouse button
* Add own personal Contra layout
* Enable auto-shifting
* Enable tap dancing and implement Space Cadet-like shift with LSHIFT and ENTER
* Implement Colemak Mod-DH layout, clean up Adjust layer
* Implement keyboard and keymap refactor
More info: https://github.com/qmk/qmk_firmware/pull/3191
* Update the readme.md and keymap.c files for Colemak
* Add include guard, make layout description cleaner
* Updated info.json for Duck Jetfire
Generated a new info.json file. @mechmerlin asked my help in debugging this file. Firmware works as expected if built from source, but not if built from the Configurator.
* Corrected the position of the arrow keys in LAYOUT_all
* Add my own keymap to the list of available Redox keymaps.
This keymap is a Colemak keymap, and is meant to be used on Mac OS.
More information can be found in the readme.
* Fix "macOS" typo and remove mention of the license.
This directory inherits the project's license.
* Add missing custom keycode.
* Address feedback from PR review
- Remove deprecated code
- Remove RGB logic since it is overwritten by code running later.
* Added HHKB with 7U space bar
There are backlight changers on the function Z, X and C, mediat controls
have been removed.
* Fixed the default layout and added a keymap
GUI and ALT keys were swapped.
My own keymap which adds calculator, removes power, removes eject.
* Adjusted naming convention of hhkb layout layer
Fixed as per required from code review.
* Updated for qmk configurator
I didn't realise that there was a new standardisation across all the keymaps to accommodate the configurator.
Hopefully fixed now.
* rename 68_ansi layout to 65_ansi layout
* more renames and readme change
* add company names
* add community layouts for 68_ansi
* add 68_ansi support for mf68 type boards
* update readme
* - Fixed DK60 version in config.h
* - Updated dk60 readme with new QMK rules
* - Fixed wording in readme
* Added dbroqua layout for DZ60
I've also updated dz60.h to add "true HHKD" keymap definition (6U
spacebar).
With the default HHKB definition r_alt was not mapped and when I pressed
r_menu it was r_alt.
Regards
* Updated dbroqua layout for HHKB keyboard
Added default configuration and alternate (swap gui/alt keys).
Save user choice in keyboard memory (like plank, thanks for this
feature!).
* Added dbroqua layout for Iris keyboard
* Updated layout and fixed includes
* Added personal layout for FC660C
* Inverted ESC & GRV
Corrected the make examples by adding the parent directory.
Updated the QMK Docs links for the build environment setup and the make instructions. Added links to the Newbs Guide.
* CTRL LED scan code mapping fix
Fixed scan codes to properly align with key wiring
* Update scan codes for caps and scroll lock lighting
Update scan codes for caps and scroll lock lighting according to previous scan code mapping update
* Added new Marianas keymap for DZ60
* Included suggestions to remove unnecessary line regarding MODS_CTRL_MASK, and added names for layers.
Added enum to define names for layers, and removed unused #DEFINE
* added my lukaus keymap (programmers dvorak with QWERTY, function, and mouse/keypad layers)
* updated ergodox_ez keymap and initial commit for IBM Model M 122 key
* added my lukaus keymap (programmers dvorak with QWERTY, function, and mouse/keypad layers)
* updated ergodox_ez keymap and initial commit for IBM Model M 122 key
* Add keyboard information and separated my custom layout from the default
* Add readme to Lukaus' Ergodox EZ keymap
* added my lukaus keymap (programmers dvorak with QWERTY, function, and mouse/keypad layers)
* updated ergodox_ez keymap and initial commit for IBM Model M 122 key
* added my lukaus keymap (programmers dvorak with QWERTY, function, and mouse/keypad layers)
* updated ergodox_ez keymap and initial commit for IBM Model M 122 key
* Add keyboard information and separated my custom layout from the default
* Add readme to Lukaus' Ergodox EZ keymap
* added my lukaus keymap (programmers dvorak with QWERTY, function, and mouse/keypad layers)
* updated ergodox_ez keymap and initial commit for IBM Model M 122 key
* Fix merge conflict again?
* updated ergodox_ez keymap and initial commit for IBM Model M 122 key
* Add keyboard information and separated my custom layout from the default
* Add readme to Lukaus' Ergodox EZ keymap
* added my lukaus keymap (programmers dvorak with QWERTY, function, and mouse/keypad layers)
* added my lukaus keymap (programmers dvorak with QWERTY, function, and mouse/keypad layers)
* updated ergodox_ez keymap and initial commit for IBM Model M 122 key
* updated ergodox_ez keymap and initial commit for IBM Model M 122 key
* Add keyboard information and separated my custom layout from the default
* update keymap
* Update rules.mk to remove redundant commented line
* Fix missing key on default layout for IBM Model M 122 key
* Fix issues identified by drashna and noroadsleft
* Update readme for IBM 122 key
* Add am keymap
* Add configuration to play nice with stuck modifiers
This is in particular useful with emacs since its easy to get ctrl stuck
* Deactivate mouse keys and backlight
* Add control/esc and shift/enter taps
* Remove DVORAK and PLOVER
I won't be using this soon, so getting some free space
* Raiser and Lower ideas from jeebak
* Add cursor and mouse layers
* Enable mouse keys
* Switch underscore with minus
* Disable audio and fix warnings
* Update to the upstream changes
* VIM line motion symbols on the raise layer
* Enable sound and freeup some media keys on layers
* Fix whitespace on keymap
* Code review changes
* Improve keymap documentation
* Improve keymap to match to the default one
* Restore DEFAULT_FOLDER to the default value
* Fix config.h unescaped line
Added support to enter bootloader from software (bootloader version must be newer than "v2.18Jun 22 2018 17:28:08" until workaround for older is created).
Updated CTRL and ALT keymaps for entering bootloader with Fn+b held for >500ms.
Added basic MacOS keymap for ALT.
USB sleep LED indicator now turns off after 1 second.
Slowed down debug LED code printing.
* mitosis:datagrok: fix typo'd inconsistent brace arrangement
(thank you @cari66ean)
* mitosis:datagrok: add makefile argument MITOSIS_DATAGROK_SLOWUART
* mitosis:datagrok: return backspace to opposite space, use TT(), more
- move backspace back to its position opposite space
- move del to red+backspace
- move tab back to tap-leftshift
- move printscreen/scrolllock/pause to blue+left pinky column
- use TT() instead of MO() to stick a layer on if wanted
- indentation that my text editor wants
- default to no audio; i can enable it at compile time.
* mitosis:datagrok: modularize features, add default layer rotator key
* mitosis: add MITOSIS_DATAGROK_BOTTOMSPACE makefile argument
* mitosis:datagrok: README improvements; document new features
* mitosis:datagrok: dot. not "number pad dot." in numbers layer
* mitosis:datagrok remove unnecessary _user audio code
* mitosis:datagrok: return to MO() for red/blue, keep TT() for purple
in this way, the LED still updates quickly when red or blue is pressed,
but we can still lock the purple layer on for 10-key numpad operation
with red+tapping blue.
* mitosis:datagrok: add colemak and dvorak default layers
* mitosis:datagrok update readme re: available default layouts
* mitosis: remove unneeded code that was overriding led_set_user
also, add some comments
* mitosis:datagrok: updated led setting code for new layers
also, place into led_set_user where it belongs, not matrix_scan_user.
* mitosis:datagrok: update LEDs when setting the default layer
maybe this should go into default_layer_set?
* mitosis:datagrok update readme with new imgur links + other improvements
* mitosis:datagrok fix typo in image urls
* mitosis:datagrok remove useless #include (ty @drashna)
* mitosis:datagrok undo unnecessary change to quantum/quantum.h
i can put the extern float definition in my own keymap code. (ty @drashna)
* mitosis:datagrok move customized layout to my keymap
no need to modify keyboard-level mitosis.h. (ty @drashna)
* mitosis:datagrok update comment describing my led indicator logic
* datagrok:mitosis update readme to document LED indicator.
* swap KC_LALT with KC_LGUI
* replace KC_RALT with KC_RGUI
This makes the keyboard more mac friendly out of the box (I'm aware this
that this could partially be done in software with the preferences but
hey, where's the fun in that).
* fixing ortho_4x12 configs
* Using upstream/master version instead
* Additions and Corrections
Corrected the Kinesis/Stapelberg's .c file to allow LEDs to work
Removed excess cruft from my Kinesis keymap to reflect this change
Other minor tweaks and adjustments to my ortho_4x12 and 5x12 layouts
* Rules for vitamins_included
Added a section to disable RGB underglow for the Let's Split
Vitamins Included board.
* fixing ortho_4x12 configs
* Using upstream/master version instead
* Additions and Corrections
Corrected the Kinesis/Stapelberg's .c file to allow LEDs to work
Removed excess cruft from my Kinesis keymap to reflect this change
Other minor tweaks and adjustments to my ortho_4x12 and 5x12 layouts
* Creating my own userspace
* Added Rorschach keymap
* renamed userspace folder
I renamed my userspace folder since I'm not ready to start using
it just yet, and I want to get my keyboards programmed. This is
a temporary thing and will be fixed later as I get time.
* adding files in "new" folder
* Disabling LEDs on Pro Micro
* Modifications to Kinesis keymap
* More kinesis tweaks
* removed userspace from master
Created a new branch for my userspace stuff. I'll work on it there.
* Moved keymap to separate branch
Moved the Rorschach keymap I was working on to a separate branch
for development purposes. Not ready to push it up to upstream
master.
* pulling in diverge tm2 from staging branch
* cleaned up comments, docs, licenses
* refactored apparent grid to make 2u spacebars more obvious
* various delinting from noroadsleft review
* most of drashna's feedback responded to
- lots of lint swept
- used more modern tri-layer functions
- still need to adopt modern split support.
* switch to common split code. remove comment cruft
* tapping force hold makes LT way more usable for rapid , sequences
* improvement of crkbd communication functions (based on helix-keyboard)
* Removed unnecessary code.
* Changed read restriction from #define to #pragma once.
* Changed from sizeof to defined size.
* moved lib folder to crkbdroot.
removed warning of ws2812.d
* - Fixed DK60 version in config.h
* - Updated dk60 readme with new QMK rules
* - Fixed wording in readme
* Added dbroqua layout for DZ60
I've also updated dz60.h to add "true HHKD" keymap definition (6U
spacebar).
With the default HHKB definition r_alt was not mapped and when I pressed
r_menu it was r_alt.
Regards
* Updated dbroqua layout for HHKB keyboard
Added default configuration and alternate (swap gui/alt keys).
Save user choice in keyboard memory (like plank, thanks for this
feature!).
* Added dbroqua layout for Iris keyboard
* Updated layout and fixed includes
* Added personal layout for FC660C
* Add support for my Falbatech Atreus
This is currently the default Atreus keyboard layout, but I will
eventually customize it to match my Ergodox layout.
* Address review comments
* More review comments fixed
* More review comments fixed
Renamed keyboard alt67 to alt and adjusted necessary files where alt67 appeared.
CTRL keymap fixed enum structure name.
usb2422 removed stray define no longer used.
* new mode for v60
xtonhasvim. still working on it:
- need to get indicator lights going
- and fun layer properly fleshed out.
* status lighting, proper fun layer
copied fun layout from keycaps to maximize accessibility
* enable power return
* support brightness adjustment for indicators
* refined brightness setting.
is saved in eeprom now
* readme. and fixed tilde
* more modifiers fall through fun layer
* i mean, this kinda works..
* much more reliable way of restoring lights
* responded to feedback
* various edits and minor additions
* updates
* updates
* updates
* lets_split LEDs off instructions
* lets_split LEDs off instructions
* turn off lets_split LEDs in userspace
* one-hand setup for right side
* Massdrop keyboards readme update
Massdrop keyboards readme update for flashing instructions
* ctrl and alt keyboard readme update
Updating make command in Massdrop CTRL and ALT keyboard readme files to reflect directory change
This is the simplest, most efficient way I could come up with to silence
the "Failed to start write 60" error that occurs when QMK tries to talk
to a screen that doesn't exist.
iota_gfx_init passes a success boolean. We catch that into a global bool
(we could rewrite multiple functions to pass this as an argument, but
given the number of keyboards using this code it seemed less disruptive
this way) and then use that as a conditional on running the
iota_gfx_task in matrix_scan_user.
Tl;dr: if the screen doesn't init, the screen write code doesn't run.
* Massdrop SAMD51
Massdrop SAMD51 keyboards initial project upload
* Removing relocated files
Removing files that were relocated and not deleted from previous location
* LED queue fix and cleaning
Cleaned some white space or comments.
Fix for LED I2C command queue.
Cleaned up interrupts.
Added debug function for printing numbers to scope through m15 line.
* Factory programmed serial usage
Ability to use factory programmed serial in hub and keyboard usb descriptors
* USB serial number and bugfix
Added support for factory programmed serial and usage.
Incorporated bootloader's conditional compiling to align project closer.
Fixed issue when USB device attempted to send before enabled.
General white space and comment cleanup.
* Project cleanup
Cleaned up project in terms of white space, commented code, and unecessary files.
NKRO keyboard is now using correct setreport although KBD was fine to use.
Fixed broken linkage to __xprintf for serial debug statements.
* Fix for extra keys
Fixed possible USB hang on extra keys report set missing
* I2C cleanup
I2C cleanup and file renames necessary for master branch merge
* Boot tracing and clocks cleanup
Added optional boot debug trace mode through debug LED codes.
General clock code cleanup.
* Relocate ARM/Atmel headers
Moved ARM/Atmel header folder from drivers to lib and made necessary makefile changes.
* Pull request changes
Pull request changes
* Keymap and compile flag fix
Keymap fix for momentary layer.
Potential compile flag fix for Travis CI failure.
* va_list include fix
Fix for va_list compile failure
* Include file case fixes
Fixes for include files with incorrect case
* ctrl and alt67 keyboard readme
Added ctrl and alt67 keyboard readme files
* Add german layout for redox keyboard
A german layout for the redox keyboard which tries
to stay close to the default english redox layout
while acommodating the umlauts at their usual position.
* Fix keycodes in german redox keymap
The keycode for Y was wrong.
* Minor changes
* Remove #ifdef include guard by #pragma once
* Remove unnecessary include from rules.mk
* Review changes
Remove unnecessary code fragments that
were pointed out in the review
of PR #3695 by @drashna.
* Adding the AT101 PCB firmware
* Fixed AT101 keymap error
* Fixing AT101 firmware
* More Fixes for AT101 firmware
* Rename AT101_Blackheart.c to at101_blackheart.c
* Rename AT101_Blackheart.h to at101_blackheart.h
* Update readme.md
* Renaming AT101 folder pt1
* Renaming AT101 folder pt2
* Fixing AT101 LED function name
* Redoing AT101 folder naming pt2
Last round had issues, should be the last rename.
* Fixing missing comma in at101_blackheart.h
* Make tap function inline
* Use better makefile keyboard detection
* Remove Copy-Paste macro
* Add F11/F12 to Iris
* Minor tweaks to userspace config
* Set audio clicky randomness to 1.5
* Set NO_DEBUG to only be set if console is not enabled
* Move NO_MUSIC_MODE to userspace config.h
* Reduce Ergodox Debounce
* Add Planck Light config
* Use OSM for ortho 4x12
* Music Mode changes for planck light
* Cleanup do to shutdown user and other fixes in Master
* Add and use 'shutdown_user' fzunction
* Remove global NO_MUSIC_MODE define
* Add NO_MUSIC_MODE to individual keymaps
* Change layer colors
* Remove NO_PRINT and NO_DEBUG from userspace config.h
Since these are automatically disabled if the console isn't enabled.
* Remove backlight code if backlight isn't enabled
* Remove Twinkle from Ergodox
* Disable RGB twinkling and enable PSM
* Clean up RGB matrix code
* Clean up planck light indicators
* Clean up tap code
* Rules cleanup for ortho 4x12
* Fix up userspace template
* Revert "Clean up tap code"
This reverts commit 09f64d6d67aa021c3b5ac86a9a739a5ca2b9c1ec.
* Organize includes
* userspace cleanup
* Fix modifier spelling error
* Fix userspace rules
* Disable Permissive Hold again
* Minor clean up
* Fix Tap stuff
* Viterbi Updates for file size
* fixed arrow keys and left control
* added right shift
* latest version
* reverted arrow keys
* edited readme
* added osu layer
* updated osu layout
* updated osu layout
* added full arrow keys to osu layout
* in case i mess up creating macros
* added the best meme key in the world
* added plover steno layer
* updated boy314 layout
* removed unused layers
* added boy314 xd75 layout, inspired by preonic layout
* added boy314 xd75 layout, inspired by preonic layout
* version 2 of boy314's xd75 layout
* added readme notes
* updated readme for boy314 xd75 layout
* qwerty support, brackets on bottom row, caps lock underglow
* fixed readme/
* small changes to allow merging
* minor changes to format
* fixed up default readme
* Keyboard: HandWired/XeaL60
* Updated rules.mk
* Mapping for layout was flipped
* Figured out how to re-map bad pins.
* Updated Keymap
* Enabled audio, Forced NKRO
* Added QMK_KEYS_PER_SCAN
* Removed more unnecessary files, since split_keyboards are in main QMK branch already.
* Simplified rules.mk in rev1
* Removed i2c from matrix.c
* Re-formatted to 4 spaces per tab,
* Changed note for NUMPAD
* Added I2C support back!
* Fixed keyboard mappings. Both sides work
* Moved i2c configuration from keymaps/default/config.h to config.h
* Changed SCL_CLOCK to 400000L
* Added DEBUG_MATRIX_SCAN_RATE for future optimization efforts
* Removed row2col code to clean up matrix.c
* Scan rate from 2100 -> 4200 by using Nop instead of waiting 30us between columns.
* Further optimized column reading via optimized_col_reader.
* Immediate key-recognition
* Switched back to own implementation of SPLIT_KEYBOARD. Will optimize so that slave interrupts master.
* Moved scanrate debug messages to another file.
* Made matrix_scanrate.c compile if CONSOLE_ENABLE is off. Updated to latest i2c.c
* Latest i2c uses a few bytes for lighting information
* Optimizations in i2c.h to determine buffer size.
* Disabled a whole bunch of features. TODO: Test that keyboard still works fine.
* Minimum #define NO_ACTION's with still working keyboard
* Fixed matrix not working due to offsets not being respected
* Added numlock button for keymap.
* Use I2C_KEYMAP_START offset
* Removed serial, Backlight and RGB support
* Removed need for split_flags.
* Added audio on and off for numlock.
* Renamed from xeal60 to xealous, simplified build system.
* Used more shared split_common code.
* Updated audio code.
* moved tone_qwerty and tone_numpad to config.h. Removed keymaps/default/config.h
* Added more shortcut keys in _FN layer. Increased debounce to 6ms due to fencepost error.
* DF used with incorrect argument. Custom_keycodes no longer required.
* Fixed bug in update_debounce_counters which was resulting in no debouncing!
* Removed unnecessary #include
This small change prevents an unused variable from being initialized, throwing a warning during compilation, thus ending fatally.
[07:47:10] [Daniels-MacBook-Pro-3] [dburkhol] [ /Users/dburkhol/git/qmk_firmware ] [develop ]
: make handwired/dactyl:default
QMK Firmware 0.6.97
Making handwired/dactyl with keymap default
avr-gcc (GCC) 7.3.0
Copyright (C) 2017 Free Software Foundation, Inc.
This is free software; see the source for copying conditions. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
Size before:
text data bss dec hex filename
0 19972 0 19972 4e04 .build/handwired_dactyl_default.hex
Compiling: keyboards/handwired/dactyl/twimaster.c [OK]
Compiling: keyboards/handwired/dactyl/matrix.c keyboards/handwired/dactyl/matrix.c:52:22: error: 'expander_col_pins' defined but not used [-Werror=unused-const-variable=]
static const uint8_t expander_col_pins[MATRIX_COLS] = MATRIX_EXPANDER_COL_PINS;
^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
[ERRORS]
|
|
|
make[1]: *** [.build/obj_handwired_dactyl_default/matrix.o] Error 1
make: *** [handwired/dactyl:default] Error 1
Make finished with errors
* Move octagon directory into duck diretory and fix as many compile issues as I can
* fix formatting
* fix layout75 matrix
* edit readme for build instructions
* Bocaj Layout Revamp
* Pull in Upstream (#1)
* Various tweaks for some Input:Club build processes
* change KEYMAP to LAYOUT for all new keyboards made using this script
* Add support for rev3 of the Atom47 (#2672)
* Added support for rev3 of the Atom47
* Updated Atom47 readme's
* Fix redefine error on rev2 and add maartenwut's keymap
* Fix redefine error on LEdiodes keymap
* Add Nyquist keymap (#2692)
* nyquist
* danielhklein nyquist setup
* shift left controls
* remove readme
* cleanup before pr
* ready for pr
* Adds Phantom TKL support (#2696)
* Add an info.json to phantom keyboard
* Add layouts
- KEYMAP_WINKEYLESS
- KEYMAP_7BIT
- KEYMAP_ISO
- KEYMAP_ISO_WINKEYLESS
* Add key_counts
* Add 2 missing F-Row keys
* Add TKC1800 info.json
Created an info.json for the tkc1800.
* Clueboard 60 info.json
- adds
- LAYOUT_60_ansi
- LAYOUT_60_iso
- KEYMAP_AEK
- KEYMAP
- LAYOUT_60_ansi_split_bs_rshift
* Add the Speedo keyboard
* Fix KC60 info.json file (#2707)
* change KEYMAP to LAYOUT in all the KC60 files
* Redo the info.json file
* Small fixes to TKC1800
- adjust F-row to use 0.25 spacing
- split left shift
- add key_count
* Fix some Configurator Warnings regarding LAYOUT vs KEYMAP (#2708)
* change diverge 3 KC_KEYMAP to LAYOUT
* Change KEYMAP to LAYOUT for handwired arrow pad
* change M10A to LAYOUT for m10-a
* Change KC_KEYMAP to LAYOUT_kc and KEYMAP to LAYOUT for mf68
* change KC_KEYMAP to LAYOUT for nano
* Refactor to LAYOUT
* refactor to LAYOUT-ansi and LAYOUT_iso for s65
* LAYOUT conversions for lfkkeyboards
* missed a few renames
* mini1800 for lfkeyobards support of LAYOUT
* Improve state/chord handling and clean up namespace
Some values that can never, ever, change were held in local
variables, rather than in PROGMEM. Fixed.
Change "pressed" to a signed int so the test for < 0 makes
sense, and to avoid possible weird failure modes in the
case where a key release comes in when pressed is already
zero. (Shouldn't happen, sure, but computers are weird.)
A lot of things in process_steno had external linkage for no
particular reason. They've been marked static. Stuff still
builds.
Distinguish between currently-held keys and keys that have
been held, and expose these values through a nicely-named API
so other code could, say, check on the current set of steno
chording in order to make displays. Also in passing fix up the
"state" value having external linkage so it could clash with
other people's variable declarations.
The API also provides hooks for key processing and steno chord
events, so you can monitor those events without having to
run in matrix_scan_user and recheck the values directly. Also
document these.
There is no path through processing a key that doesn't
end with a return false, so the nested return foo() are
gone and we just return false.
* Pull information from config.h and rules.mk (#2711)
* Pull information from config.h and rules.mk
* Readd the kbd75 maintainer
* Remove obsolete info.json entries (#2712)
* Clean up some long-standing errors when populating the API (#2715)
* More Configurator Warning Fixes (#2716)
* mf68_ble did not have the correct .c and .h files
* Fix JC65 KEYMAP to LAYOUT
* Change KEYMAP to LAYOUT for s60_x
* Convert KEYMAP to LAYOUT for lets_split boards
* Convert KEYMAP to LAYOUT
* more fixes to keymap for iris
* convert KEYMAP to LAYOUT for levinson keyboard
* change losinggeneration's KEYMAP to LAYOUT
* convert KEYMAP to LAYOUT
* convert KEYMAP to LAYOUT for nyquist
* convert KEYMAP to LAYOUT
* convert KEYMAP to LAYOUT for viterbi
* convert KEYMAP to LAYOUT
* convert KEYMAP and its subsidiries to the LAYOUT standard
* convert KEYMAP and its subsidiries to the new LAYOUT standard
* Normacos keymap for let's split keyboard (#2691)
* Cheers let's split keymap
* fixed typo on norman layer of cheers keymap for let's split
* fixed right handed mappings for home row
* cheers keymap for let's split redefinition
* updated Cheers keymap for let's split
* cheers keymap for let's split updated with some terminal macros
* renamed cheers let's split keymap to a more appropriate normacos
* updated normacos keymap doc / removed non functional keys
* reset let's split rules to default values
* added more spotlight search macros
* normalized keymap comments
* Moved numpad on lower layer
* hhkb jp personal keymap (#2698)
* Add JJ40 Cockpit personal keymap (#2713)
* Add JJ40 Cockpit keymap
* Fix lower layer symbols
* Add readme for "major" keyboards to eliminate more QMK Configurator errors (#2718)
* add readme to ktype keyboard
* add readme to m10a
* add readme to mini1800
* add readme to parent directory
* Revert "Pull in Upstream (#1)"
This reverts commit eeba0cec17ccb636e4225eed88aeae72b99f5e45.
* Updates to Bocaj Files
- Gave up on Tap Dance for ' -> '
+ Added another 'Secret'
+ Add ' -> ' to the Swap Hands key
+ Add Swap Hands to the ' -> ' key
+ Made Hand Swapping a momentary toggle
- Removed Auto Shift
+ Added Layer Toggle to KC_QUOTE for the _TOOLS layer
- Disabled Tap Dance
* Merge remote-tracking branch 'upstream/master'
* Updates to Bocaj
Added Game Layers, Removed Unused Macros
* Removed 'secrets.h'
* Updates to Bocaj
Remove 'secrets'.
Remove 'sendstring_workman.h' and set related layer back to qwerty due to macro compatibility issues
* Total revisioning of keymap and layout structure
* Missed readme.md file
* Bocaj - Permissive Hold setting enabled
* Switching from ErgoDox EZ centric configuration to the layout/user approach
* Bocaj - Create Userspace and Ergodox layout
* Update settings.json
* Adding my personal planck keymap
* Adding readme.md to my keymap
* Create my userspace
add users/ishtob/
* Moved macros off keymap
macros now exsists in my userspace, moved them off keyboard specific keymaps
* Create my userspace
add users/ishtob/
* rebase from main QMK repo
* fixed compile error with planck rev6 keymap
* fixed compile error with planck rev6 keymap
* Revert "Merge branch 'master' of https://github.com/ishtob/qmk_firmware"
This reverts commit 6c8a9a6eec7ec311802338ea361099612182465d, reversing
changes made to 5c598d9a53a7f794d5be283ac40ca97631ae5578.
* fixed issue where compile errors if private macro file is not present
* Revert "fixed issue where compile errors if private macro file is not present"
This reverts commit e0035df48ffb9a95aa94e8339c58ef539e0449cf.
* Fixed STM32 timer issue with Planck Rev6 with tap mods
* Revert "fixed compile error with planck rev6 keymap"
This reverts commit 5c598d9a53a7f794d5be283ac40ca97631ae5578.
* Revert "Revert "fixed compile error with planck rev6 keymap""
This reverts commit c36896ca718f8b9bb3c653d7532797e9129477e3.
* Fixed compile issues with my personal userspace and keymap utilizing the userspace
* Initial Commit
Port from xauser's jetfire code. Does not compile yet
* fix up keymap from uint8 to uin16
* update rules file to contain custom matrix
* Good stopping point
Still lots of compile errors but I'm getting there.
* fix a few more compile errors
* move a few functions around to help with compiling
* Finally got it all to compile
* Get rid of that old KEYMAP macro
* edit readme
* Put my name everywhere and some minor code clean ups
* start to remove that kc nonsense
* fix keymap compilation issues
* add reset key info
* better human readable formatting
* match the duck default layout
* add confgurator support
* clarify reset key
* might be a good idea to use the correct pin
* get the riight keycode for RGB
* include an ALL layout
* I tried to fix the formatting....sigh
* add functons to ensure Configurator compile-ability
* move jetfire to duck directory
* Moved and renamed things as per Drashna's PR comments as his back was hurting as he reviewed this
* AMJ96 Refactor
LAYOUT matrix and default keymap refactored to use full-length keycodes (instead of shorthand).
* Configurator update
Minor physical layout update and made the labels more sensible.
* Readme update
White space correction.
* Default keymap update: #include QMK_KEYBOARD_H
* rules.mk update
Disabled the following options as my local test compile's .hex ended up too big to fit in the available flash space:
MOUSEKEY_ENABLE
EXTRAKEY_ENABLE
BACKLIGHT_ENABLE
RGBLIGHT_ENABLE
If this is undesirable, suggestions are welcome.
* Config/rules update
Re-enabled MOUSEKEY_ENABLE, EXTRAKEY_ENABLE, BACKLIGHT_ENABLE, and RGBLIGHT_ENABLE and disabled COMMAND_ENABLE in rules.mk; enabled NO_ACTION_MACRO and NO_ACTION_FUNCTION per @drashna
* Swapped `___` for `XXX` in amj96.h per @mechmerlin
* add configurator support
* update bface code to more modern QMK standards
* update readme
* update readme
* Make changes thanks to noroadsleft's PR comments
* first verion of skug
* zudvp layer added and new thumb cluster
* move del to arrw cluster and switch places of algr and no_circ
* first verion of skug
* zudvp layer added and new thumb cluster
* move del to arrw cluster and switch places of algr and no_circ
* rework layouts
* Adds SYMB layer toggle to 'ä'
Closes#2
Also moves ctrl away from '-' and 'z' to the outer bottom corners
and removes redundant SYMB layer binds from there
* Adds mouse movement to right hand on ARRW layer
Closes#3
* Fix typoed keycodes
* planck qwerty nordic
* Update README.md
* Update README.md
* Implemented changes to planck layout requested by drashna
* Implemented changes to ergodox layout requested by drashna
NOTE: `version.h` is still required.
* Added support for the b.face keyboard
This commit adds support for the 60% keyboard from winkeyless, the
b.face. The basic keyboard layout as well as the RGB backlighting
works as expected; the per-key LEDs can be turned on or off but not
yet dimmed. A default 60% US-layout is included.
* Added link to the bface in the ps2avrGB README
* add my config
* fix backlight, clean up that code
* group background code, restore static var
* qwerty is supposed to be in the middle
* wrap layer change backlight in ifdef
* backlight levels and some more 'emojis'.
* Restructure to make it possible to press cmd ent on the right side of the board with one hand.
* Expose the period through the number layer. Add Hyper keys to mouse layer
* reduce mouse speed
* add a : -P key
* Thumbs up and down, remove some keys that are duplicated via function keys, clean up
* fix build issues
* add various emoji
* duplicate default Meira keymaps
* Miera updates
* add documented but unmapped emoji
* Sound for the Meira, was stumped by a file size! Thanks drashna!
* add docs
* docs
* revert lib changes...
* clean up
* clean up
* remove make file
* Fixes missing key
* clean up
* add my lets split
* add more emoji
* add the telophase board (unofficially, I guess...)
* add missing files
* add/reset files
* Review feedback implementation: Not needed. Add #define FLIP_HALF to your config.h file instead.
* Review feedback implementation: All of these includes should be replaced with #include QMK_KEYBOARD_H.
* Review feedback implementation: [FAILING] You may want to use LAYOUT_ortho_4x12 instead, and move this to /layouts/community/ortho_4x12/ instead. That way, you can use the same keymap for all of the boards.
* clean up
* add a key for command tilde (osx loves it)
* at least its building again
* remove adjusts and migrate layer switching to MO(_LAYER)
* update the telophase readme
* update the telophase readme
* grahampheaths -> grahampheath
* ONEHAND_ENABLE -> SWAP_HANDS_ENABLE
* convert lets split to use ortho_4x12
* Move lets split keyboard layout into community/ortho_4x12
* make telophase use LAYOUT()
* I did it?!
* Add clap and grin
* swap tabs and back and forward
* whitespace
* initial commit
* update readme
* enable/disable some keyboard features and add 60_ansi community layout support
* put my name everywhere
* can't use numbers for defines
* enable lighting
* put in a default keymap, use the correct pins, and put in a switch matrix
* update switch matrix to use KXY hex notation
* add QMK Configurator support
* add the rest of my name
* update where to get this keyboard
* Implement magic 8-ball mode for big series switch
* LED Testing
* Add Ctrl+Alt+Del key mapping
* Add Windows lock (win+L) layout.
* Add Big Series 3-key
* Add Big Series 4-key
* Add Big Series 2-key
* Fix layout mapping for Big Series 3u
* Fix merge-conflict.
* Refactor bigseries boards into a single folder
* Add biacco-biacco keymap
* Change P position
* Update biacco-biacco map y position
* Revert y position...
* Refactor needless lines
* Fix some review commentted
* Obelus Refactor: LAYOUT to LAYOUT_ortho_4x4
- Keymap also now uses #include QMK_KEYBOARD_H
- Readability and white space changes
- rules.mk now has LAYOUTS = ortho_4x4
- added info.json
* naKey Refactor: LAYOUT to LAYOUT_numpad_5x4
- Matrix LAYOUT renamed to LAYOUT_numpad_5x4
- Now supports community layout numpad_5x4
- White space changes
* naKey Configurator update
Updated order of JSON objects to match new matrix order.
* initial commit and get pins correct
* get the switch matrix done
* Add Configurator support
* update LED numbering
* enable lighting options
* add a default-ish keymap
* turn off mouse keys as the file gets too large
* put my name everywhere
* update Alf names
* update keymap to match whats on qmkeyboard.cn
* Matrix refactor: eagle_viper/v2 LAYOUT_all
- Deleted K0L (research indicates no switch position at this location)
- Renamed K0J to K0I (spacebar key; on 9th column instead of 10th)
- Updated info.json and default keymap to match
- readability updates
* Keymap refactor
readability update
* Revamp replicaJunction keymaps
Updates both the replicaJunction Ergodox and Atreus keymaps and moves
most of the logic into a new user directory.
* Cleanup as requested in #3589
* Slightly increased TAPPING_TERM
* Fixed typo in #pragma once
* Fix TAPPING_TERM redefined in config.h
* Add include of replicaJunction.h
Due to the tap dance references, without this include, I was getting
compiler errors about both internal QMK items like
`qk_tap_dance_state_t` and constants defined in my replicaJunction.h
file like TD_LAYER_TOGGLE.
Also remove some commented-out code that defined an enum which has since
moved to replicaJunction.h.
* Created base sixshooter configuration
* Added SixShooter basic LED on/off support.
* Updated LED identifier numbers to align with layout identifiers (and IDs on PCB).
* Minor sixshooter documentation cleanup.
* Added sixshooter info.json file.
* Moved sixshooter custom keycodes out of keymaps and into base keyboard files, small documentation tweaks.
* Removed unnecessary boot section size definition.
* Removing CONFIG_H if/define and replacing with #pragma once.
* Adding my personal planck keymap
* Adding readme.md to my keymap
* Create my userspace
add users/ishtob/
* Moved macros off keymap
macros now exsists in my userspace, moved them off keyboard specific keymaps
* Create my userspace
add users/ishtob/
* rebase from main QMK repo
* add change_reciver2sender()/change_sender2reciver()
This is a change to improve readability.
* txled, rxled off in matrix_init()
* add serial_send_packet() / serial_recive_packet()
This is a change to reduce object size.
* add serial_low() at ISR() top
* add __attribute__((always_inline)) to some functions
* modify serial_send_packet()/serial_recive_packet()
A little, object size reduction.
A little, speedup.
* add debug code to helix/serial.c
* Adjust sampling timing of serial signal being received
* add split_scomm.c/split_scomm.h and change serial.c/serial.h
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
* add split_scomm.c/split_scomm.h into helix/rev1
* reduce object size helix/rev2/matrix.c
* remove checksum check, add parity check
* force occur parity error for test
* parity test ok. remove test code
* change some comment & add skip code when buffer_size == 0
* serial.c: multiple types of transaction support
Add 4 bits transaction-type field at packet top.
Select Transaction Descriptor Table entry by transaction-type.
* helix serial master-slave transaction optimize
Using multi-type transaction feature of serial.c, communication contents between master slaves were optimized.
* add debug code for retry
* add comment into each config.h
* fix ISR status drop
* add a debug macro 'debug_retry_chg()'
* reduce led_test size
* remove debug code from helix/serial.c and etc.
* helix:five_rows change TAPPING_TERM value 140
* Improved compatibility with let's split of serial.c. Finish helix/serial.c improvement.
- The difference with the original let's split's serial.c
- It's high-speed about 4 times.
- Stable bi-directional data transfer. (Helix need master to slave transfer)
- serial.h was divided 2 files, serial_config.h and sereial.h
- With multiple types of transaction support, communication contents can be optimized. (NEW flexible API)
- USE OLD Simple APIs (compatible with let's split serial.c)
- files :
- serial_config.h -- hardware configuration (need include by config.h)
- serial.c/serial.h -- serial communication
- USE NEW flexible APIs. (Support multi-type transaction function.)
serial.c was divided into 2 layers, split_scom.c and serial.c.
The upper layer split_scomm.c is called from matrix.c.
The lower layer serial.c accesses the hardware.
- files
- split_scomm.c -- communication buffer is defined in here. call by matrix.c.
- split_scomm.h -- buffer size is defined in here. include by matrix.c, split_util.c
- serial_config.h -- hardware configuration (need include by config.h)
To use the NEW API, specify #define SERIAL_USE_MULTI_TRANSACTION
- serial.c/serial.h -- serial communication lower layer
- NEW APIs for serial.c / serial.h (The lower layer)
// Soft Serial Transaction Descriptor
typedef struct _SSTD_t {
uint8_t *status;
uint8_t initiator2target_buffer_size;
uint8_t *initiator2target_buffer;
uint8_t target2initiator_buffer_size;
uint8_t *target2initiator_buffer;
} SSTD_t;
// initiator is transaction start side
void soft_serial_initiator_init(SSTD_t *sstd_table);
// target is interrupt accept side
void soft_serial_target_init(SSTD_t *sstd_table);
int soft_serial_transaction(int sstd_index);
int soft_serial_get_and_clean_target_status(int sstd_index);
- NEW APIs for split_scomm.c / split_scomm.h (The upper layer)
move from old serial.c the following buffer and functions
serial_slave_buffer[]
serial_master_buffer[]
void serial_master_init(void)
void serial_slave_init(void)
int serial_update_buffers(void)
define SERIAL_xxxxx_BUFFER_LENGTH move from serial_config.h to split_scomm.h
<!-- http://www.keyboard-layout-editor.com/#/gists/c1e8a15c68e4c52eed84653f21ae2d29 -->
Designed specifically to make switching back-n-forth with the Apple's MacBook Pro keyboard intuitive. Has a slight tendency toward readline/vim keybindings.
Caps locks becomes an `Esc` when pressed alone, or a `Ctrl` when pressed with another key.
Base Layer
----------
As simalar to the Apple keyboard as possible. Notiable exception is `Caps Lock`:
- `Esc` when pressed alone
- `Ctrl` when pressed with another key
Control+ Layer
--------------
Left `Ctrl` key switches to the "Control+ Layer". This layer mostly acts like a control key in most cases, with a few exceptions:
- `Ctl+` + `hjkl` are vim-style motion keys
- `Ctl+` + `p` and `Ctl+` + `n` are page up and down
- `Ctl+` + `Backspace` is forward delete
Fn Layer
--------
Audio Controls:
- `Fn` + `a` Volume Down
- `Fn` + `s` Volume Up
- `Fn` + `d` Mute
To flash this layout you need to press `Fn+Backspace`
Designed specifically to make switching back-n-forth with the Apple's
MacBook Pro keyboard intuitive. Has a slight tendency toward
readline/vim keybindings.
Caps locks becomes an `Esc` when pressed alone, or a `Ctrl` when pressed
with another key.
Base Layer
----------
As simalar to the Apple keyboard as possible. Notiable exception is
`Caps Lock`:
- `Esc` when pressed alone
- `Ctrl` when pressed with another key
Control+ Layer
--------------
Left Ctrl key switches to the "Control+ Layer". This layer mostly acts
like a control key in most cases, with a few exceptions:
- `Ctl+` + `hjkl` are vim-style motion keys
- `Ctl+` + `p` and `Ctl+` + `n` are page up and down
- `Ctl+` + `Backspace` is forward delete
Fn Layer
--------
Audio Controls:
- `Fn` + `a` Volume Down
- `Fn` + `s` Volume Up
- `Fn` + `d` Mute
To flash this layout you need to press `Fn+Backspace`
* Adds Fleuron keyboard directory and default layout
* Adds Fleuron keyboard directory and default layout
* adds double zero macro, and updates to the new macro methodology
* adds raise and lower layers
* removes makefile from default layout, turns off mousekey, console, and command in rules.mk
* makes upper right key a bksp in default layout, adds .json layout file
* updates to default layout
* tweak default layout jusabit
* fix raise and lower switch case, and scoot a few keycodes around
* make changes for PR #3571
* fixing erros for PR #3571
* adds Dollartacos first custom keymap
* fixes for PR #3571
* Initial Commit of catch22 macropad by rockydbull
* Add configurator info.json
* Use macros
* Use pragma once
* Use CA22 as product id
* Clean up readme
* Use the layer define value
* Feedback from @drashna
* initial commit
* get the matrix correct
* make my name be known
* add rgblight enable
* add a default keymap
* Add QMK Configurator support for the base layout
* add name here too
* fix up readme
* remove set user from keymap
* use led_set_kb as per drashna's comments on PR
* cloned colinta as base
* switched to default base. started customising
* minor changes to layout
* added mouse keys
* minor tweaks to layout and mouse speed
* updated readme
* tweaked layout
- added middle fn keys
- moved rgb controls to fn layer middle
- added special keys to fn layer right
* moved scroll buttons as to not interfere with lshift
* turned on backlight
* fixed backlight
* changed user keycodes to differentiate
* changed folder name to lowercase
* updated readme
* stop processing after custom keycode
* edits to suit new standards
* added layer indicator using gp100 and gp103
* Rules for vitamins_included
Added a section to disable RGB underglow for the Let's Split
Vitamins Included board.
* fixing ortho_4x12 configs
* Using upstream/master version instead
* Additions and Corrections
Corrected the Kinesis/Stapelberg's .c file to allow LEDs to work
Removed excess cruft from my Kinesis keymap to reflect this change
Other minor tweaks and adjustments to my ortho_4x12 and 5x12 layouts
* Updated readme
* dz60/macos_arrow: move the eject key on esc to leave right cmd+bksp for move to trash
* dz60/macos_arrow: move the reset key on the media layer
This avoids accidental activation.
* dz60/macos_arrow: disable LEDs
* jennetters fourier keymap, tapdance declarations and reformatted keymap file for readbility
* Update rules and keymap to follow new makefile setup.
* Add #pragma once to config.h
* add SCREEN_NAV layer for copy/pasting within screen
* working readreg/paste macros
* working read reg / paste macros
* write log and tran patterns, and expand
* add ls -la shortcut, add tab on combined layer
* put delete word on the right pinky key on shell_nav layer
* add TAB on the right side, add reset key
* added Cloud9 macros
* add cloud9 shortcuts to atreus layout
* added BROWSER_CONTROL layer
* finalized browser control layer
* adding comment
* add browser control layer to atreus
* add flashing command line
* remove the tab on combined layer
* remove the tomouse
* remove mouse layer, change log/tran expand patterns, cleanups
* add dumptlog macro
* add "delete to home" shortcut
* fix conflict
* remove unneeded mouse layer
* add meh shortcuts on the browser_control layer
* add/modify some macros
* explain the various layers
* Add files via upload
Added a nordic layout for UT47
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Add files via upload
* Update to readme and keymap files
* Update readme.md
Changed cover image
* Update readme.md
typo fix
* Delete config.h
* Delete keymap.c
* Delete readme.md
* Delete rules.mk
* Updated cover image in readme.md
Fixed typo in image of keymaps
* Update keymap.c
Changed backslash to forward slash in first function layer.
* Add files via upload
* Delete config.h
deleting files so I can upload to a folder with lower case name
* Delete keymap.c
deleting file so I can change to lower case name
* Delete readme.md
deleting file so I can change to lower case name
* Add files via upload
* Update keymap.c
Cleaned up definitions in beginning of file.
* Update keymap.c
forgot an include
* Update keymap.c
* Update readme.md
Updated picture of layout, link was wrong and pointed to an old/removed image.
* Update readme.md
Fixed error in link to keyboard layout editor
* Update keymap.c
More cleanup of the includes at beginning of file
* Update config.h
* Update keymap.c
Fixed typo: Volume Down and Volume Up on the Tab layer were switched.
* Update keymap.c
* Added a macro on the Tab layer for <kbd>Ctrl</kbd>+<kbd>Alt</kbd>+<kbd>Del</kbd>
* Added a macro on the Gaming layer for <kbd>Alt</kbd>+<kbd>Tab</kbd> (replaces prebious Backspace key)
* Update readme.md
Updated readme.md file to reflect changes to keymap.c in cover photo and KLE link.
(added short cuts for Ctr Alt Del and Alt Tab)
* fix for that stupid LED
* formatting changes and add firmware flashing warning to readmes
* update readme with more info
* add LAYOUT_60_ansi thanks to help from phlop
* add configurator support for 60_ansi
* add 60_ansi for community layout support
* Bocaj Layout Revamp
* Pull in Upstream (#1)
* Various tweaks for some Input:Club build processes
* change KEYMAP to LAYOUT for all new keyboards made using this script
* Add support for rev3 of the Atom47 (#2672)
* Added support for rev3 of the Atom47
* Updated Atom47 readme's
* Fix redefine error on rev2 and add maartenwut's keymap
* Fix redefine error on LEdiodes keymap
* Add Nyquist keymap (#2692)
* nyquist
* danielhklein nyquist setup
* shift left controls
* remove readme
* cleanup before pr
* ready for pr
* Adds Phantom TKL support (#2696)
* Add an info.json to phantom keyboard
* Add layouts
- KEYMAP_WINKEYLESS
- KEYMAP_7BIT
- KEYMAP_ISO
- KEYMAP_ISO_WINKEYLESS
* Add key_counts
* Add 2 missing F-Row keys
* Add TKC1800 info.json
Created an info.json for the tkc1800.
* Clueboard 60 info.json
- adds
- LAYOUT_60_ansi
- LAYOUT_60_iso
- KEYMAP_AEK
- KEYMAP
- LAYOUT_60_ansi_split_bs_rshift
* Add the Speedo keyboard
* Fix KC60 info.json file (#2707)
* change KEYMAP to LAYOUT in all the KC60 files
* Redo the info.json file
* Small fixes to TKC1800
- adjust F-row to use 0.25 spacing
- split left shift
- add key_count
* Fix some Configurator Warnings regarding LAYOUT vs KEYMAP (#2708)
* change diverge 3 KC_KEYMAP to LAYOUT
* Change KEYMAP to LAYOUT for handwired arrow pad
* change M10A to LAYOUT for m10-a
* Change KC_KEYMAP to LAYOUT_kc and KEYMAP to LAYOUT for mf68
* change KC_KEYMAP to LAYOUT for nano
* Refactor to LAYOUT
* refactor to LAYOUT-ansi and LAYOUT_iso for s65
* LAYOUT conversions for lfkkeyboards
* missed a few renames
* mini1800 for lfkeyobards support of LAYOUT
* Improve state/chord handling and clean up namespace
Some values that can never, ever, change were held in local
variables, rather than in PROGMEM. Fixed.
Change "pressed" to a signed int so the test for < 0 makes
sense, and to avoid possible weird failure modes in the
case where a key release comes in when pressed is already
zero. (Shouldn't happen, sure, but computers are weird.)
A lot of things in process_steno had external linkage for no
particular reason. They've been marked static. Stuff still
builds.
Distinguish between currently-held keys and keys that have
been held, and expose these values through a nicely-named API
so other code could, say, check on the current set of steno
chording in order to make displays. Also in passing fix up the
"state" value having external linkage so it could clash with
other people's variable declarations.
The API also provides hooks for key processing and steno chord
events, so you can monitor those events without having to
run in matrix_scan_user and recheck the values directly. Also
document these.
There is no path through processing a key that doesn't
end with a return false, so the nested return foo() are
gone and we just return false.
* Pull information from config.h and rules.mk (#2711)
* Pull information from config.h and rules.mk
* Readd the kbd75 maintainer
* Remove obsolete info.json entries (#2712)
* Clean up some long-standing errors when populating the API (#2715)
* More Configurator Warning Fixes (#2716)
* mf68_ble did not have the correct .c and .h files
* Fix JC65 KEYMAP to LAYOUT
* Change KEYMAP to LAYOUT for s60_x
* Convert KEYMAP to LAYOUT for lets_split boards
* Convert KEYMAP to LAYOUT
* more fixes to keymap for iris
* convert KEYMAP to LAYOUT for levinson keyboard
* change losinggeneration's KEYMAP to LAYOUT
* convert KEYMAP to LAYOUT
* convert KEYMAP to LAYOUT for nyquist
* convert KEYMAP to LAYOUT
* convert KEYMAP to LAYOUT for viterbi
* convert KEYMAP to LAYOUT
* convert KEYMAP and its subsidiries to the LAYOUT standard
* convert KEYMAP and its subsidiries to the new LAYOUT standard
* Normacos keymap for let's split keyboard (#2691)
* Cheers let's split keymap
* fixed typo on norman layer of cheers keymap for let's split
* fixed right handed mappings for home row
* cheers keymap for let's split redefinition
* updated Cheers keymap for let's split
* cheers keymap for let's split updated with some terminal macros
* renamed cheers let's split keymap to a more appropriate normacos
* updated normacos keymap doc / removed non functional keys
* reset let's split rules to default values
* added more spotlight search macros
* normalized keymap comments
* Moved numpad on lower layer
* hhkb jp personal keymap (#2698)
* Add JJ40 Cockpit personal keymap (#2713)
* Add JJ40 Cockpit keymap
* Fix lower layer symbols
* Add readme for "major" keyboards to eliminate more QMK Configurator errors (#2718)
* add readme to ktype keyboard
* add readme to m10a
* add readme to mini1800
* add readme to parent directory
* Revert "Pull in Upstream (#1)"
This reverts commit eeba0cec17ccb636e4225eed88aeae72b99f5e45.
* Updates to Bocaj Files
- Gave up on Tap Dance for ' -> '
+ Added another 'Secret'
+ Add ' -> ' to the Swap Hands key
+ Add Swap Hands to the ' -> ' key
+ Made Hand Swapping a momentary toggle
- Removed Auto Shift
+ Added Layer Toggle to KC_QUOTE for the _TOOLS layer
- Disabled Tap Dance
* Merge remote-tracking branch 'upstream/master'
* Updates to Bocaj
Added Game Layers, Removed Unused Macros
* Removed 'secrets.h'
* Updates to Bocaj
Remove 'secrets'.
Remove 'sendstring_workman.h' and set related layer back to qwerty due to macro compatibility issues
* Total revisioning of keymap and layout structure
* Missed readme.md file
* Bocaj - Permissive Hold setting enabled
* Add files via upload
Added a nordic layout for UT47
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Add files via upload
* Update to readme and keymap files
* Update readme.md
Changed cover image
* Update readme.md
typo fix
* Delete config.h
* Delete keymap.c
* Delete readme.md
* Delete rules.mk
* Updated cover image in readme.md
Fixed typo in image of keymaps
* Update keymap.c
Changed backslash to forward slash in first function layer.
* Add files via upload
* Delete config.h
deleting files so I can upload to a folder with lower case name
* Delete keymap.c
deleting file so I can change to lower case name
* Delete readme.md
deleting file so I can change to lower case name
* Add files via upload
* Update keymap.c
Cleaned up definitions in beginning of file.
* Update keymap.c
forgot an include
* Update keymap.c
* Update readme.md
Updated picture of layout, link was wrong and pointed to an old/removed image.
* Update readme.md
Fixed error in link to keyboard layout editor
* Update keymap.c
More cleanup of the includes at beginning of file
* Update config.h
* Update keymap.c
Fixed typo: Volume Down and Volume Up on the Tab layer were switched.
* Added initial files for QC60 prototype
* renamed all 'keymap' to 'layout'
* renamed layout macros to suggested naming convention of LAYOUT_macro_description
* replaced boilerplate
* removed rules.mk from keymap folders
* replaced 'qc60/rev1' with 'qc60/proto'
* replaced more boilerplate
* renamed DEFAULT_FOLDER to point at the correct folder
* updated readme
* Add files via upload
Added a nordic layout for UT47
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Add files via upload
* Update to readme and keymap files
* Update readme.md
Changed cover image
* Update readme.md
typo fix
* Delete config.h
* Delete keymap.c
* Delete readme.md
* Delete rules.mk
* Updated cover image in readme.md
Fixed typo in image of keymaps
* Update keymap.c
Changed backslash to forward slash in first function layer.
* Add files via upload
* Delete config.h
deleting files so I can upload to a folder with lower case name
* Delete keymap.c
deleting file so I can change to lower case name
* Delete readme.md
deleting file so I can change to lower case name
* Add files via upload
* Update keymap.c
Cleaned up definitions in beginning of file.
* Update keymap.c
forgot an include
* Update keymap.c
* Update readme.md
Updated picture of layout, link was wrong and pointed to an old/removed image.
* Update readme.md
Fixed error in link to keyboard layout editor
* Update keymap.c
More cleanup of the includes at beginning of file
* Update config.h
* fabian layout
* added MOUSECURSOR layer that gets activated by holding space
* cleanup, meh and tilde and grave as separate keys, toggle switch for mousecursor layer
* merged default
* #pragma once
* including QMK_KEYBOARD_H instead of various imports
* using layer toggle instead of a function
* deleted obsolete rules.mk (was part of the old makefile system)
* #pragma once
* including QMK_KEYBOARD_H instead of various imports
* use ifndef KEYBOARD_planck_rev6 instead of ifdef KEYBOARD_planck_rev5
* Temporary work around for CB60 sound issues
Discussed this with @fredizzimo, upping the system ticks to 100K fixes
the sound issues I was having with the CB60; speaker would fail to shut
off after playing music, sometimes at startup. This changes the matrix
scan time from it's default of every 2ms to once ever 200us.
Fred has a more extensive change to the way matrices are scanned which
will require less clock cycles and we can then revert this change at
that time.
* Remove keymap dir from clueboard root
* Arrow: matrix and keymap refactor
* Left: matrix and keymap refactor
* Numpad: matrix macro correction
* Numpad: add support for community layouts numpad_5x4 and ortho_5x4
* Right: matrix and keymap refactor
* DC01 global readme cleanup (minor grammar)
* DC01 global Configurator support
* Right: bugfixes for HHKB-style keymaps
* Replace KC_NO with ___ in matrices for readability
* Add K49 to LAYOUT matrix
K49 was previously was stated to be padless, but it's actually the right-hand half of a split Backspace.
* Switched positions of K3C and K3D in LAYOUT matrix
When using a split right Shift, K3D is to the left of K3C.
* Insert KC_NO (___) element into bottom row of LAYOUT_60_ansi matrix
Reported by @NimMooMoo on QMK Discord
Right-hand modifiers on bottom row were shifted one key to the right. After debugging, discovered that the "electrical matrix" (the part of the matrix macro that determines which row and column a key uses) was one element short on the last row at K49, causing the rest of the row to be offset by one column.
This commit corrects that issue.
* Added a missing comma in the LAYOUT matrix
* Moved F row to raise
* Moved mouse keys over one space and removed unneccessary code
* Moved delete on lower
* Added CTRL functions
* Added Print Screen
* Added README.md file
* Updated CTRL
* Updated readme to current CTRL
* Minor Changes
* Updated mouse speeds
* Unknown changes
* Updated README and keymaps
* Removed caps from number row and put it in special
* Moved around equals sign again
* Updated mouse key speed
* Pull Request Updates
* Put in my keymaps
* Fixed all but weird lets split issue
* Organized and tried to trobleshoot lets split
* Organized and tried to trobleshoot lets split
* Added bbaserdem keymaps
* Added bbaserdem keymaps
* Fixed stuff
* FIxed a filename error
* Lets split eh
* Finalized things regarding keymap
* LFKPad: matrix refactor
* LFKPad: keymap refactor (QMK_KEYBOARD_H; matrix update)
* LFKPad: Configurator support
* LFKPad: added community layout numpad_6x4 to rules.mk
* LFKPad: Update rgb_sequence to match new matrix
* LFKPad: delete deprecated makefile include block from rules.mk
* DC01 initial commit
- Addition of directories
- Left readme
* Initial commit of left half
* Initial files for right half
* arrow
* i2c adjustments
* I2C slave and DC01 refractoring
- Cleaned up state machine of I2C slave driver
- Modified DC01 left to use already pressent I2C master driver
- Modified DC01 matrixes
* Fixed tabs to spaces
* Addition of Numpad
* Add keymaps
- Orthopad keymap for numpad module
- Numpad keymap for numpad module
- ISO, ANSI and HHKB version of keymap for right module
* Minor matrix.c fixes
* Update Readmes
* Add support for LFK65-HS - a hotswap 65%
* Add info.json for LFK65-HS
* Clean up for new build system, remove uneeded code.
* LFK65-HS cleanup. Fixed LAYOUT macros, etc
* Line ending stuff again
* Added Let's Split Eh? Files and updated #USE_IC2 checks to also include th EH revision (can only be used in I2C)
* Added personal keymap, updated some of the EH files
* Created new keyboard file for testing "lets_split_eh" will merge into lets_split once fully functional
* Added split code from lets_split, removed pro micro imports and LED code
THIS IS WORKING CODE, WITHOUT RGB AND BACKLIGHT
* Took back original Lets Slit files for the lets_split keyboard, working in the lets_split_eh folder for now
* Updated eh.c
* More rework of the I2C code, added global flags for split boards.
* Introduced RGB over I2C, having weird edge case issues at the moment though
* Fixed weird I2C edgecase with RGB, although still would like to track down route cause..
* Changed RGB keycodes (static ones) to activate on key-up instead of key-down to elimate weird ghosting issue over I2C
* Lots of changes, mainly externalized the Split keyboard code and added logic for only including when needed.
- Added makefile option "SPLIT_KEYBOARD" that when = yes will include the split keyboard files and custom matrix
- Split keyboard files placed into quantum/split_common/
- Added define option for config files "SPLIT_HAND_PIN" FOr using high/low pin to determine handedness, low = right hand, high = left hand
- Cleaned up split logic for RGB and Backlight so it is only exectuted / included when needed
* Updated documentation for the new makefile options and #defines specific to split keyboards
* Added a bit more info to docs, so people aren't confused
* Modifed Let's Split to use externalized code, also added left and right hand eeprom files to the split_common folder
* Removed some debugging from eh.c
* Small changes to keyboard configs. Also added a default keymap (just a copy of my that_canadian keymap).
* Added a README file to the Let's Split Eh?
* Changed it so RGB static updates are done on key-up ONLY for split boards rather than all boards. Also fixed leftover un-used variable in rgblight.c
* Updated default keymap and my keymap for Let's Split Eh? Updated the comments so it reflects RGB control, and removed audio functions.
* Fixed lets_split_eh not having a default version
* Removed "eh" references from lets_split folder for now
* Took lets_split folder from master to fix travis build errors, weird my local was overriding.
* Changed LAYOUT_ortho_4x12_kc -> LAYOUT_kc_ortho_4x12 to match bakingpy and others
* Removed rules.mk from my lets_split keymap, not needed
* Updated the config_options doc to better explain the usage of "#define SPLIT_HAND_PIN"
* Fixed split_common assuming I2C for RGB and Backlight. Added serial backlight support (stole from bakingpy's Levinson code ;) ) Serial RGB not implemented yet. Also Added "USE_IC2" to the lets_split_eh/eh as that was looked over.
* Fixed stupid mistake, forgot to set BACKLIT_DIRTY to false after setting slave backlit settings for serial
* Updated backlight data block to be cleaner (thanks drashna ;) )
* Add files via upload
Added a nordic layout for UT47
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Update readme.md
* Add files via upload
* Update to readme and keymap files
* Update readme.md
Changed cover image
* Update readme.md
typo fix
* Delete config.h
* Delete keymap.c
* Delete readme.md
* Delete rules.mk
* Updated cover image in readme.md
Fixed typo in image of keymaps
* Update keymap.c
Changed backslash to forward slash in first function layer.
* Add files via upload
* Delete config.h
deleting files so I can upload to a folder with lower case name
* Delete keymap.c
deleting file so I can change to lower case name
* Delete readme.md
deleting file so I can change to lower case name
* Add files via upload
* Update keymap.c
Cleaned up definitions in beginning of file.
* Line ending stuff again
* Added Let's Split Eh? Files and updated #USE_IC2 checks to also include th EH revision (can only be used in I2C)
* Added personal keymap, updated some of the EH files
* Created new keyboard file for testing "lets_split_eh" will merge into lets_split once fully functional
* Added split code from lets_split, removed pro micro imports and LED code
THIS IS WORKING CODE, WITHOUT RGB AND BACKLIGHT
* Took back original Lets Slit files for the lets_split keyboard, working in the lets_split_eh folder for now
* Updated eh.c
* More rework of the I2C code, added global flags for split boards.
* Introduced RGB over I2C, having weird edge case issues at the moment though
* Fixed weird I2C edgecase with RGB, although still would like to track down route cause..
* Changed RGB keycodes (static ones) to activate on key-up instead of key-down to elimate weird ghosting issue over I2C
* Lots of changes, mainly externalized the Split keyboard code and added logic for only including when needed.
- Added makefile option "SPLIT_KEYBOARD" that when = yes will include the split keyboard files and custom matrix
- Split keyboard files placed into quantum/split_common/
- Added define option for config files "SPLIT_HAND_PIN" FOr using high/low pin to determine handedness, low = right hand, high = left hand
- Cleaned up split logic for RGB and Backlight so it is only exectuted / included when needed
* Updated documentation for the new makefile options and #defines specific to split keyboards
* Added a bit more info to docs, so people aren't confused
* Modifed Let's Split to use externalized code, also added left and right hand eeprom files to the split_common folder
* Removed some debugging from eh.c
* Small changes to keyboard configs. Also added a default keymap (just a copy of my that_canadian keymap).
* Added a README file to the Let's Split Eh?
* Changed it so RGB static updates are done on key-up ONLY for split boards rather than all boards. Also fixed leftover un-used variable in rgblight.c
* Updated default keymap and my keymap for Let's Split Eh? Updated the comments so it reflects RGB control, and removed audio functions.
* Fixed lets_split_eh not having a default version
* Removed "eh" references from lets_split folder for now
* Took lets_split folder from master to fix travis build errors, weird my local was overriding.
* Changed LAYOUT_ortho_4x12_kc -> LAYOUT_kc_ortho_4x12 to match bakingpy and others
* Removed rules.mk from my lets_split keymap, not needed
* Updated the config_options doc to better explain the usage of "#define SPLIT_HAND_PIN"
* Use string with delay
* Add skipped region to ergodox
* Add send string config
* Use default_layer_state instead of function
* Fully generalize keyboards
* old iris cleanup
* Fix Drashna keymap compile issues
By checking to see if secret.c exists before actually trying to add it
* Remove unnecessary references
* Add 4x12 ortho board
* Update userspace readme for secrets
* Make RGB more modular
* Fix iris keymap, since we don't need the lower left (Function keys)
* Fix includes
* Add Blanks
* Fix Ergodox lower layer
* Add suspend commands
* Add Maltron Layout
* Add additional layouts
* Finish adding gamepad to Iris
* Tweaks to iris gamepag layer
* make gaming layers more friendly
* minor gaming layer tweak
* Add Carplax
* Add modded key timer function
* Cleanup and macro documentation
* Add QMK DFU info
* Add 'old' keymap for 12 LED spare
* Update Pro Micro documentation
* Disable twinkling so it fits in firmware space
* Switch to QMK DFU bootloader, since it's better anyhow
* Write default layer state colors to EEPROM
Since we are writing to EEPROM anyways, and this way, it sticks on reboot
* Fix QMK DFU bootloader options
* More updates for QMK DFU support
* Use matrix scanning hack for startup_user until #3113 gets merged
* Fix indicator light consistency issue
* Add/readd ifdefs to indicators
* Add/readd alt indicator
* Remove RGB Twinkling from Viterbi macro pad
* Fix default layer color detection
* Fix rebase and detection issues
* Cleanup code so it will compile if RGBLIGHT is disabled
* Revert vsode settings
* Use Pragma Once instead of boilerplate code
* initial files for rev 6 with encoder
* music map init, dip scan added
* adds ws2812 driver for arm
* flesh out dip and encoder support
* adds default encoder res
* adds default encoder res
* start muse implementation
* muse working with encoder as control
* flip direction
* try mouse wheel again
* dont break other revs
* dont break other revs
* conditional autio
* pwm ws driver (not working)
* update build includes for chibios
* update ws2812 driver/config
* last commit for glasser code
* working example
* remove rgb for now
* finish up rev6
* working encoder keycodes
* add warnings to planck keymaps about the LAYOUT
* - Fixed DK60 version in config.h
* - Updated dk60 readme with new QMK rules
* - Fixed wording in readme
* Added dbroqua layout for DZ60
I've also updated dz60.h to add "true HHKD" keymap definition (6U
spacebar).
With the default HHKB definition r_alt was not mapped and when I pressed
r_menu it was r_alt.
Regards
* Updated dbroqua layout for HHKB keyboard
Added default configuration and alternate (swap gui/alt keys).
Save user choice in keyboard memory (like plank, thanks for this
feature!).
* Added dbroqua layout for Iris keyboard
* Updated layout and fixed includes
* Turn backlight support on by default
* Correct error on LED backlight support
Turns out, it doesn't work if you don't enable it in rules.mk. Who knew?
* mitosis:datagrok: improved tenkey layout; changelog + more in README
* mitosis:datagrok enable audio!
* mitosis:datagrok: underscore on right shift, rearrange some symbols
* mitosis:datagrok: add more descriptions to readme
* mitosis:datagrok: abuse space cadet to get equivalent of RSFT_T(KC_UNDS)
Friend was having trouble with their tada since their build environment wasn’t setup. Updated so they could access the links that were listed (old links 404’d)
* default keymap refactor: QMK_KEYBOARD_H include; readability
* Configurator support
* info.json was missing a comma
* Added matrix functions to matrix.c per @drashna
* Moved info.json to rev1 directory
* rev1 info.json metadata update
* Configurator support for ErgoDash rev2
* Moved rev1/ergodash.h to ergodash.h
* Integrate rev2 support into ergodash.h; delete rev2/ergodash.h
